How gas boiler control operating costs

For enterprises, the control costs, reduce the budget, operational problems when the company is of particular concern. As the power plant boiler operation to promote, in all sectors of the basic necessities of life has its presence. Wherein the gas boiler having a low pollutant emissions and high combustion thermal efficiency, higher safety performance significant advantages, in particular, is widely applied in terms of industrial production and heating systems.

Industrial gas boiler room Standard Operating Procedures industrial gas boiler room Standard Operating Procedures industrial gas boiler blast furnace ready to start: gas system: check the gas pressure and the internal combustion engine are matched pressure is normal, not too high or too low, continue under normal circumstances confirm Next. Water supply system: Check the water softening equipment running, the indicators softened water should comply with the relevant national standards. Check level gauge, level indicator switch must be opened, to prevent false water level, to avoid heating the intake air. Check pump for watering, otherwise opening the exhaust valve until the water so far. Stop watering until the water level of 2/3. Close filling pumps and valves. Line pressure: Open inlet and return valve, open No. 1 or No. 2 circulation pump, watching the pressure gauge pressure is normal, the pressure range, and the exhaust air inspection system situation. Electrical system: Check that all control buttons cabinet in an open position, if not open, turn on the switch, turn on the switch to open the order is part of the master switch. Industrial gas boiler flow: System water: Open replenishment pump switch or hand switch is turned on. Another choice is to switch the pump I or II selected pump. (1) is performed before rehydration is necessary to observe whether there is water inside the water softener;. (2) while discharging water and discharged from the bottom up high-rise buildings, water supply until the water flow stable and stops. Start boiler front pump (circulation pump), to open the boiler control cabinet, open the internal switch, the cabinet door closed, the circulation pump start switch is pressed, a green light, running forehearth pump (circulation pump), so that a uniform water circulation system. Start boiler: Press the boiler switch red switch button intelligent digital boiler controller, then press the green Start / Stop button, the green light and burner wind, wait a few seconds, the engine ignition, start a normal combustion. Check the record: all the equipment and check the pipes regularly check the boiler. Industrial gas boiler start-ignition combustion: ensure the main power switch, a button to open the burner, fan sweep should begin immediately. Burner ignition failure, fault lights for 20 seconds, press the reset button to restart consecutive three or four ignition failure, successful ignition, should be reported to repair. When the burner is closed due to some failure, each system should be checked to confirm or displacement. After the fault is acknowledged and eliminated, the burner will restart.

An inner wall gas boiler leakage: the inner wall of the drum into the leakage water leakage and also the provision of water cooling pipe leakage and decreased, if the former eye is relatively small leakage can be the same Wabu steel, after Patching flaw detection. Leak needs to be replaced before the tube, replacing a large area. Second, the hand hole leaking gas boiler: re-try transducer mounted at an angle, to see if there is a hand hole cover deformation, if deformed, the first correction, green tape and then wrapped in a layer of the uniform mat, recommendations and consistent position before overhaul. Third, within the gas leaking boiler drum: the higher cost of repair costs, mainly to see the location and size of the leak leak point where, if the old boiler appears oozing red pot of water, indicating that water quality problems, probably because of low alkalinity or dissolved oxygen in the water is too high and metal corrosion. Low alkalinity can adding sodium hydroxide or trisodium phosphate to a pot of water, dissolved oxygen in water is too high to be resolved by the deaerator. Fourth, the leaking gas boiler water treatment system: first check whether the gas boiler corrosion, if you need to descaling the boiler corrosion, leaks repaired part, and then circulating water treatment, adding agents, equipment and other materials were boiler corrosion, resistance dirt, protection. V. Inner boiler flue gas leak: check is not the boiler tube or tube sheet due to cracks, if the need to change the pipe, see Wabu flue used material, aluminum, and stainless steel may be carbon steel or aluminum wire TIG iron material may be directly acid electrode. Sixth, gas boiler leaking valves: Valves leaking should be home packing or replace the valve.

In the process of cooperation with Lulu, the company has maintained a serious and responsible attitude and enthusiasm, any after-sales problems in a timely manner to communicate and resolve site or through the network. Lulu's relevant person in charge to give us feedback, we buy fast boiler is not only fast because of strong party strength, but also because of the powerful party fast service, any improper operation can get our phone to remind party fast remote monitoring, this allows us to use very reassuring. --customer feedback