Power plant shx 65 t 1 25mpa inner circulating anthracite coal fired boiler working principle

Power station boilers are an indispensable device in thermal power plants. They generate high-temperature and high-pressure steam by burning various fuels (coal, oil, natural gas, biomass fuel, etc.). This steam is used to drive a steam turbine. Generator attached to the steam turbine generating electricity.

Steam Boiler Types in Brewery

ZG Boiler as a professional industrial steam boiler manufacturer, mainly supplies coal fired steam boiler, biomass fired steam boiler, oil & gas fired steam boiler, waste heat steam boiler, CFB steam boiler to customers. ZG supply brewery steam boilers for beer processing and the steam boiler usually used in brewery is gas fired steam boiler and biomass fired steam boiler. The gas fired steam boiler and biomass fired steam boiler in ZG Boiler has proved ISO9001-2008 certification and also pass through ASME and IBR certification, and both of them are reliable to choose.

Note the use of an industrial shx 65 t 1 25mpa inner circulating anthracite coal fired boiler fan which 1, strengthen the operation and management, ban illegal operation. Industrial boiler drum fan up and running, there must be strict rules. The induced draft fan starts to be unloaded, non-load starting, particularly when the boiler stoked, flue gas temperature is too low, such as the induced draft fan starts with load (i.e., open the blower inlet damper or fully open), a current will start increased a lot, and start-up time is too long, the fan motor can overheat, overloading is likely to burn out; when the boiler (particularly pulverized coal) Jan-fire operation, pay attention to drums, fan's opening sequence, can not be reversed. I.e., first open fan, run for 10 minutes, and to exclude the furnace flue fouling or flammable gases, before the blower starts. If the first open blower, the induced draft fan, so that both the induced draft fan load is increased, so that the induced draft fan motor overheating burned, and the furnace may lead to explosion. 2, industrial boiler flue gas dust removal blowers take measures to regularly clean the flue, induced draft fan to improve the working environment. Dust removal equipment units to strengthen the dust removal operation and management, improve the efficiency of dust removal; no dust removal equipment units to time quantitative dosing into the boiler furnace special cleaning agents, and timely removal of fouling of the flue, the flue avoid clogging, the impeller damage accidents. 3, the impeller blade surface hardening treatment to improve the wear resistance of the blade. Since the large fan boiler drum conveying high temperature flue gas is about 200 ℃, the flue gas contains large amounts of fly ash, SO2 and other corrosive gases, badly worn fan blades, fan output prone to drop, vibration, such as rupture of the blade. Therefore, to deal with a serious face or wear parts of welding blades to improve the wear resistance of the blade. Use DC welder welding, arc welding using manual method using a dedicated fan hardfacing strip (e.g., wear No. 1, Mo-Cr-B carbide electrode wear, etc.), and the electrode wear in 300 ~ 350 ℃ drying 1 hour use. Before welding, the surface of the blade should be fouling, rust cleaned, preheated to 100 deg.] C, with a small current, low voltage, temperature and speed, short arc welding symmetry. Practice has proved that, after surfacing treated leaves, wear resistance greatly improved, not only changed the fan impeller often wear, but also laid a good foundation for the safe operation of the fan. 4, insist on Boiler Fan periodic overhaul, maintenance of strict quality control. Industrial boiler drum Fan to be overhauled on a regular basis. The elimination before the accident hidden danger in the bud, to overhaul a comprehensive, thorough, carefully check the wear, the impeller shaft and impeller balanced operation, with or without internal connections loose, collision, inlet baffle switch is flexible and bearing lubrication and cooling Happening.

Beiqi Panther car 6 tons of steam condensing one fuel gas steam shx 65 t 1 25mpa inner circulating anthracite coal fired boiler project has been successfully completed. This series boiler adopt advanced design concepts, using the waste heat of flue gas cascade, with the use of the condenser and the economizer fully absorb the waste heat in the flue gas, the boiler efficiency has been greatly improved.