What a steam boiler performance was uneven heat? The following is a non-uniformity reasons: 1, non-uniform heat absorption of the steam boiler. Closely related to the arrangement, operation mode and the type of fuel causes nonuniform heat absorption of the burner. Uneven temperature distribution in the furnace, the heat causes a small load intensity of each furnace waterwall. In general, in the case where the same type of fuel, the heat load distribution in the furnace slagging liquid much larger than the heat load distribution in the furnace slagging solid. Fuel burner heat load is larger than the unevenness of the uneven heat load fired furnace, hot offset vertical tube panel screen than the horizontal tube thermal excursions. DC endothermic steam boiler unevenness different from the natural circulation steam boiler. Natural circulation steam boiler having a heat compensation characteristics, can play a major role in reducing thermal excursions, but the evaporator heating surface in direct steam boiler, heat absorption for larger tube, because the steam generation amount of the inner tube, large capacity . Increase the resistance, the flow rate of the steam pipe is reduced. Conversely, increasing the flow rate of weak heating pipes. Therefore, the DC steam boiler evaporator heating surface will not only cause non-uniform endothermic thermal excursions, but also to expand the non-uniform heat flow by influencing the deviation. 2. The flow rate of the steam boiler is not uniform. Electric heating boiler and the boiler is mainly composed of electric control box and control system. Its characteristics are environmentally friendly, clean, no pollution, no noise, automatic, with limited energy and reduce prices significantly, as a new boiler electric heating boiler equipment increasingly being recognized. Electric heating the core member is electrically heated boiler, directly determines the life of the boiler, to select a non-metallic electrical heating tube (such as a ceramic heating pipe), because it is resistant to the load, a long life, and a water separation structure, the boiler Wing no leakage. Biomass boiler is a kind of boiler to biomass energy as a boiler fuel called biomass boilers, steam boilers into biomass, biomass hot water boiler, biomass stove, biomass thermal oil heaters, vertical raw biomass boilers, biomass boilers and other horizontal. Different resistance to flow parallel to the tubes of the evaporator heating surface, and a change in pressure along the length of the header, and the difference in weight between the head tube and the tube will lead to non-uniform flow. Variation on the thermal flow resistance. Since the structure of the steam pipe, the quality, of different length, diameter, roughness and curvature, the flow resistance is different. Under the same pressure, the flow resistance can cause uneven. When the thermal head 2 in the high-pressure variation in the vertical riser screen, since the height of the larger screen, parallel tubes uneven heating, density vary greatly, it should consider the impact ram repositioning. When high heat load single tubes, the tube bundle of the flow decreases. However, due to the reduced density of the working fluid within the tube and the weight of the head is reduced, the flow rate increases. Accordingly, high pressure water is advantageous to reduce thermal excursions.

Note the use of electric heating boiler pressure which at present, advanced high-temperature atmospheric boiler, the apparatus for high temperature and pressure. Widely used in electrical, mechanical, chemical, civil heating boilers that require a large amount of heat energy industries. However, when using atmospheric electric boiler, the user should carefully take certain precautions to ensure the normal operation of equipment. First, note that the adjustment device Feed Mode Currently, electrically separated from the pressure hot water boiler system in operation stop, the user should be noted that the piezoelectric constant separation operation of boiler and heating system. In addition, users first is the lowest water level in the boiler water boiler expansion tank, and then the ground water system. Meanwhile, when the boiler is filled with water, the gas discharge apparatus requires. Second, note that the electrical ignition test apparatus boiler pressure before ignition, in addition to various auxiliary equipment inspection boilers, particular attention should be automatic opening and closing valve is sensitive and reliable, and observe the change in boiler water level. If the water level rises rapidly after the device stops operation, automatic opening and closing valve member described serious leak, the user should be serviced or replaced atmospheric electric boiler apparatus. Third, pay attention to equipment operating temperature change high pressure hot water boiler if the water temperature is too high, easily lead circulating pump inlet vaporization occurs, affecting the normal operation of equipment operation of the pump. Thus, the user should pay attention to application of electric control pressure in the boiler water temperature, water temperature of the device and the device should be controlled at 90 ℃.

For more than two decades, it has been the focus on clean boilers, the insistence on precision and wisdom, and the pursuit of exquisite craftsmanship that have made today's Fangkuai boilers. Fangkui Boiler will always be based on the boiler industry, and will return customer support and trust with brilliant results and sophisticated technology.

the main rationale original working passed to a boiler water in the container after use of the thermal energy released or the fuel burned in the industrial production of heat, the temperature of the water reaches the demanded or must steam pressure thermal equipment boiler in the "pot" and "furnace" two somewhat performed in conjunction with the water into the boiler in the future, the heat in the soda system boiler heating surface will absorb transferred to the water, the water heated to a bound of temperature and pressure generating hot water or steam, is drawn applied. in some incineration equipment, continued burning of the fuel heat release, high temperature flue gas occurs by thermal incineration of communication, transferring heat to the boiler heating surface, the temperature was gradually lowered itself, and finally discharged from the chimney classification steam boiler: a, divided by the fuel: 1, gas boiler, 2, oil-fired boiler, 3, gas boiler, 4, electric heating boilers, 5, atomic energy boiler, 6, waste heat boiler, etc., during the first four at most, the most common, the lowest operating costs of gas-fired boilers, but large area, environment pollution, the operator requested more; fuel gas boiler high degree of automation, operation cost is higher than gas, smaller footprint, fewer requests operator; electric heating boiler I have not had the operation, but the operation cost should be the highest, but a small boiler area, environmental best; other boiler is not introduced because they do not understand Second, by mode of heat transfer into the fuel gas-fired boiler is usually fire tube boiler water tube boiler, fire tube boilers, water, fire tube boilers and other. typical model: WNS series (horizontal burning boiler combustion chamber), the characteristics of such boilers: simple structure, an additional amount of evaporation is generally small (typically ten tons or less, there are also large, but usually do not exceed 35 tons), Kai boosting faster furnace, boiler water is relatively low request; gas boiler are usually water-tube boiler, water tube boiler high thermal efficiency, but messy configuration, the boiler high quality requested. Third, by additional pressure into the low-pressure boilers, pressure boiler, high pressure boiler Fourth, the use is divided into days boilers, industrial boilers, power generation, marine boilers.