Fault analysis of drinking electric hot water boiler for sale feed pumps and excluded from analysis (1) electric water pump motor to overheat and exclusion for the use of motor-driven feedwater pump is concerned, the most common failure is the motor overheating. Cause overheating of the motor is mainly due to high or low voltage, drive poor ventilation system failure or malfunction caused by overheating of the motor unit. Cause serious overheating of the motor insulation burned, where the occurrence of broken rotor bars and the like. Thus, overheating of the motor should be found in the use of pneumatic power to other ways, for downtime. Motor voltage causes overheating of the motor supply system to deal with checks, to resolve the boiler feed pump motor overheating fault by restoring stable power supply. In addition to poor transmission can also cause motor overheating due to motor and cause motor load is too large to poor transmission between the pump, the phenomenon of a small horse-drawn carts, motor overload is temperature. Such a situation must be timely maintenance, resulting in unit failure. The traditional system of the motor and pump to conduct a thorough investigation, the traditional poor common mainly due to lack of oil transmission system rotating bearing, bearing damage and other causes. Where to find the point of failure can be replaced or lubricated. One of the most common fault caused due to motor overheating when the same subsystem failure, which is mainly due to the damage to the fan, ventilation duct blockage, bearing wear and other reasons that the ventilation system can not complete the work to be undertaken, resulting in motor overheating, serious will burn coil. Such a situation must be by one investigation to find out the cause of the malfunction, unobstructed ventilation duct, fan repair, replacement of bearings can solve the problem. (2) feed pump pump pump overheated boiler feed pump overheated common reason is due to the damage caused by the bearing friction caused by or due to lack of oil lubrication system, oil is not good cause. Thus the pump after the pump was found to overheating should first check the lubrication system is short of oil or lubricating oil containing impurities, followed by investigation bearing damage. For just overheating should also check the rolling bearing of the carriage through the access cover is pump gap is too small. After the inspection the pump shaft still fever should check whether the two-axis bending or misalignment, while checking the balance of the impeller, a two-axis adjusting shaft or concentricity adjustment, remove the impeller balance holes, in order to ensure the rotation of the impeller shaft balance, troubleshooting. The main reason (3) boiler feed pump flow is insufficient boiler feed pump flow rate of the main pump leaves damage, causing pipe blockage or leak. For the use of belt driven water pump also consider whether due to belt slippage caused by the low speed caused by insufficient flow. After checking the investigation belt line, plug the leak at the still insufficient flow impeller should consider whether there is damage.

609, why the steam drinking electric hot water boiler for sale is replaced by electric heating gas steam boiler steam boiler is replaced why the electric heating gas furnace compared with the steam boiler steam, and the higher production requirements, pressure increases with increasing temperature. In recent years, new thermoelectric organic heat transfer oil furnace is also known as heat transfer oil furnace. we usually referred to as gas steam heater. it combustible gas and electrical energy to thermal conduction of the heat medium oil high oil outlet to 400c, heat device connected to the hot water more environmentally friendly and energy saving compared with the steam boiler, saving up to 40% to 55% oil furnace using electric heating and the conductive loop. different steam, the steam is directly discharged after use, heat can not be recovered heating stable, accurate temperature control. gas steam boiler and the heat transfer pipe are stable, unlike a steam boiler steam temperature fluctuations in the system, gas and steam electric furnace facilitate automatic control microcomputer electric heating oil heater low and high temperatures are secure, gas and steam heated to 340 degrees at normal pressure, does not evaporate. steam reach the same temperature, the saturation pressure 14.593MPa. hot water boiler must be in order to achieve a certain pressure High water temperature. If you want to get a temperature of 280 degrees Celsius, the pressure should be reached 6.412MPa. Therefore, gas steam heater has a good safety performance heat transfer oil furnace electric heating with low cost, low investment, easy to manufacture and so on. due to the low heat transfer oil furnace operating pressures, significantly easier to manufacture than the steam boilers and hot water boilers, low cost, small investment. in general, class E with twelve kinds of boiler or pressure vessel manufactured qualified manufacturers have the ability to produce hot oil furnace .609,

In recent years, the state environmental protection is all the more attention we as a company with the times, in order to respond positively to the implementation of the national environmental protection requirements from coal to gas project. But the choice of drinking electric hot water boiler for sale suppliers in this area quite a headache, after repeated comparison and investigation, we chose to partner with fast boiler. Fang did not disappoint quickly proved that the recommended boiler operation after use to fully meet our needs, both energy saving and environmental protection, high thermal efficiency, to a certain extent, cost savings for our fuel. --customer feedback

How to observe whether steam drinking electric hot water boiler for sale is short of water and how to deal with itSteam boiler is a kind of energy conversion equipment. The energy input to the boiler is chemical energy in fuel, electric energy, heat energy of high temperature flue gas and so on. After boiler conversion, steam, high temperature water or organic heat carrier with certain heat energy is outputted out. Water level below the minimum safe water level, or invisible water level, water table glass tube (plate) appears white. The two-color water level meter shows all the gas-phase indication colors. Low water level alarm signals occur in high and low water level alarms. Low water level interlock device, water level below the specified value should stop the operation of fan, induced fan, grate reducer motor. There is also a sharp rise in superheater steam temperature above the normal outlet Steam temperature. The exhaust temperature of the boiler rises. The feed water flow rate is smaller than the steam flow rate, if the furnace tube or coal economizer tube rupture cause water shortage, the opposite phenomenon will occur. When the water shortage is serious, you can smell the scorching smell. When water shortage is serious, red water wall tube can be seen from the furnace door. When the water shortage is severe, the furnace tube may break, and a burst can be heard, steam and smoke will be ejected from the furnace door and the fire door. By calling water; for severe water shortage, it is necessary to stop the furnace urgently, and blindly feed water to the boiler. Reduce fuel, blast, draw wind, and supply water slowly when water is classified as a slight water shortage.