Autumn and winter cold season is heating the peak of the northern city of Tianjin, with the heating period, fog, haze and other inclement weather has cropped up, as also the people a "blue sky" always in a good living environment, inside of Tianjin low-emission coal-fired boilers reform process without delay. To improve the situation of air pollution, Tianjin start the "Blue Sky Project" plans to cooperate with the fast boiler, gas boiler will invest billions of dollars in coal-fired boilers within the city as a clean fuel such as natural gas as raw material.

Plants use existing ordinary way for the steam boiler steam solutions for problems: 1, big waste of energy: pipeline transport long distance, large energy loss. Steam from the steam boiler plant to have many points have become a condensate. Especially at night discontinuous steam plant, each with steam before the need to discharge large amounts of condensate, resulting in waste of energy. 2, managers and more: Boilermakers need to arrange several on duty holder, increased labor costs. 3, beautiful plant has been greatly affected. Henan fast boiler recommended method: point - point steam supply way, needs to be placed side by side Henan steam boiler plant or equipment fast steam boiler, with the open with the use. Complete cancellation of the factory steam pipe network. And highlight the advantages of a conventional steam boiler: 1, Energy saving: Due to put an end to the pipeline transmission losses, energy-efficient way than conventional steam supply energy by 30-50%. 2, management is simple: Henan fast boiler 7 ton steam generator biomass rice husk boiler for sale boiler does not belong to the range of pressure that can be placed directly on the shop floor, without making a separate boiler room. When steam required by the plant workers can boot. 3, the plant more beautiful.

You have to know the energy consumption of boiler problems (blower power consumption rate, consumption steam) causes problems blower 1.1 boiler duct leakage. 1.2 Leakage air preheater. 1.3 excess air coefficient is too large. 1.4 coal into the furnace is deteriorated, coal from the design, the amount of coal under the same load to the generator, increasing combustion air volume. 1.5 the secondary air path resistance is increased. 1.6 low blower efficiency. 1.7 unit load is low or frequent starts and stops. 1.8 high inlet temperature. 2, the measures to solve the problem of operational measures 2.1 2.1.1 adjusted to optimize the combustion boiler according to the test results, control the excess air coefficient appropriate furnace. 2.1.2 ensure blower inlet, outlet baffle spacer in the fully open position. 2.2 routine maintenance and testing 2.2.1 blower characteristic test, to determine the optimum operating point and efficient workspace. 2.2.2 duct tightness check process. 2.2.3 damper flap defects in time. 2.2.4 timely check processing chassis, shaft seal leakage. 2.3 2.3.1 downtime in strict accordance with the provisions to adjust the fan movement gap. 2.3.2 vane opening adjustment of the blower motor. 2.3.3 check delivery port plate to open fan. 2.3.4 blower to clean the inside and imported silencer debris. 2.3.5 duct tightness check process. 2.4 transformation 2.4.1 Check and repair the fan blades, replace seriously damaged blades if necessary. 2.4.2 wave plate replacement air preheater, rinsed sector plate gap adjustment. 2.4.3 for energy saving fan efficiency below 75%. 2.4.4 Fan motor frequency energy transformation.

Boiler and its output illustrate the transformation of the group in terms of power generator: boiler, which usually have several parts which? Shell boilers, which in turn is a kind of boiler? In addition, the boiler output and power generating units, among them how conversion? These issues are on the boiler, and also we must know and master, so as to deepening the boiler products, thus, continue to acquire new knowledge in order to reach a predetermined learning objectives and requirements as soon as possible. 1. transformation of the boiler, which is typically what parts there? Boiler, part of it contains mainly two, which is specifically as follows: First, the pot of transformation, however, be noted that the transformation of its approval, is slightly more complicated, and that will take some time . First of all, there is a qualified design units to come up with rehabilitation programs, and then to the local Bureau of Technical Supervision approval, after approval by the boiler is to examine the record. When the transformation is complete, but also to test the boiler inspection. After the inspection, you can start using. Second, it is part of the transformation of the furnace, but this is much simpler, as long as the right boiler pressure part of the transformation, the transformation of other parts, is not required by the supervisory inspection. 2. shell boiler, which in turn can what? Shell boilers, which in turn can call fire-tube boiler, in its formal structure, generally a two-layer jacket. And that the outermost, is boiler shell, called the inner tube furnace. The media, is between the outer cylinder and the inner cylinder flows. Therefore, when this kind of boiler pressure, the boiler shell is subject to internal pressure, external pressure by the furnace.